Dimplex Westcott Instrucciones de operaciones descargar pdf (Pagina 6)

the contents including the xing bar (Fig 4).

Secure the xing bar using the hinge pins and after feeding 3.

the tightening bar through the xing bar, add the washers and

wingnut onto the end (1 & 2, Fig 5).

Open the sealing kit supplied and glue sealing rope into the 4.

channel on rear edge of appliance (3, Fig 6). Use suitable

protective gloves when handling glue to prevent contact. In

case of contact, wash immediately with plenty of water.

Remove the grate and the bafe plate 5. (4 & 5, Fig 7). Place the

inset stove into position in the replace and mark the intended

position of the xing screw through the hole in the bottom of

the appliance (6, Fig 7). Remove the stove and drill a hole

then insert the rawl plug supplied. Re-position the stove and

screw into place.

Create a seal with the fascia of the replace making sure 6.

the rope seal comes into contact with the fascia. Place

hand through the stove collar and tighten the wingnut on

the tightening bar (7, Fig 6). The xing bar creates pressure

when it contacts the chimney/lintel. The stove should be tightly

sealed to the replace fascia.

Floor Protection & Installation Clearances

In all instances the stove should be positioned on a non-combustible

hearth and located in a suitable solid fuel replace recess. The

construction of the hearth and replace recess must conform to

Building Regulations, must be rm, made from non-combustible

materials and capable of supporting the stove. Care should be

taken to ensure the stove is level and the hearth is secure. The

hearth itself should not be less than 125mm thick, including the

thickness of the oor and any decorative top surface (e.g. tiling).

Allow an apron of at least 225mm at the front of the stove in case

of spills when de-ashing and 150mm on either side (Fig 9 & 10).

All walls adjacent to the hearth should be made from solid non

combustible material and be made with minimum thickness as

follows:

Appliance distance

X from wall

Min Wall Thickness

Min solid wall height

300 m m abo v e the

appliance and 1.2m

above the hearth

less than 50mm 200mm

50mm and over 75mm

The minimum safe distances to combustable materials that

must be observed is 275mm to sides/front, 295mm to top.

Any surrounding combustible material should not exceed 80°C.

Room Ventilation

For safe operation this stove must be provided with combustion

air supply in addition to normal room ventilation, in accordance

with Building Regulations. Minimum ventilation requirements vary

depending on whether the dwelling is considered to be of standard

construction or of airtight construction, or if a ue draught stabiliser

has been tted. The required open air vent sizes are as follows:

Standard build dwellings {air permeability >5.0m³ /(h.m²)}

No Flue Stabiliser No additional vent required

With Flue Stabiliser 13 cm²

Airtight build dwellings {air permeability ≤5.0m³ /(h.m²)}

No Flue Stabiliser 24 cm²

With Flue Stabiliser 37 cm²

Flue Draught

The chimney should be checked before the stove is installed to

ensure that there is adequate ue pull. The draught can be checked

initially by using a smoke match close to the ue opening. If the

chimney doesn’t pull the smoke it may suggest that the chimney

- 2 -

needs further attention. Any remedial work to the chimney ue

should be carried out by a suitably Qualied Engineer.

A ue draught of minimum 12 Pascal to maximum 25 Pascal is

required for satisfactory appliance performance. The ue draught

should be checked under re at high output and if it exceeds the

recommended maximum a ue draught stabiliser (or ue damper

as it is also known) must be tted so the rate of burning can be

controlled and prevent overring.

An extractor fan must not be used in the same room as this

appliance.

Flue Damper/Draught Stabiliser (Not Supplied)

A ue damper may be tted to reduce the draught through the

stove if the draught is too high. When the damper is set in the

open position the chimney draws at full draught, increasing the

volume of air ow through the stove and ue. Shutting the damper

restricts the ow, slowing the rate of burning.

The damper should be tted to the stove ue and should be the

same size as the ue pipe. As a rule it should be tted no closer

than 700mm from the ue outlet of the appliance.

A ue damper should not be tted when burning fuels other

than wood.

Commissioning

Upon completion of installation, allow a suitable period of time for

any re cement or mortar to dry out. The stove and ue system

should then be tested by a suitably qualied person to make sure

it is safe for normal use. A smoke draw test should be completed

to check for soundness of joints and seals and also that all smoke

and fumes are taken from the appliance up the chimney and

emitted safely.

First warm the ue with a blowlamp or similar for about 10 minutes.

Place a lit smoke pellet on the centre of the grate with the air

controls open. Close the door – the smoke should be drawn up the

ue and be seen to exit from the ue terminal. Complete the test

with all windows and doors shut in the room where the appliance

is tted. If a ceiling fan is present it must be operated on max for

the duration of the test. If there are any extraction fans in adjacent

rooms these too must be operated on maximum setting during the

test with the interconnecting doors open. If any spillage occurs,

recheck the suitability of the ue system making sure there is

adequate air supply to the room (as per Building Regulations).

Light the appliance and slowly increase the temperature to medium

operating levels. The stove should not be run at full output for the

rst 3-4 burn cycles. Open the main re door when the appliance

reaches normal operating condition and carry out a spillage test

using a smoke match or pellet around the door opening. If any

spillage occurs, open all windows, allow the re to go out and

recheck the ue system and ventilation.

Operating Instructions

Please read fully these operating instructions and advise any other

users of the correct operating procedures for this stove.

Warning: The door and operating handles become hot when

the stove is in use. For your safety use the glove provided.

This stove will remain hot for a long time after the re has

extinguished. Do not operate stove with the door left open.

Initial Firing of Stove

We recommend that you have 3-4 small res before you operate

your stove to maximum heat output. This is to allow the paint to cure

and the castings to relax and consolidate location. We recommend

this ‘running in’ procedure after long idle periods to preserve the

life of the stove. During this you may notice an unpleasant smell

as paint and re cement cures. It is not toxic but for your own sake

we would suggest that during this period you leave all doors and

windows open.

1 2 3 4 5 6 7 8 9

Comentarios a estos manuales

Sin comentarios

Dimplex Westcott Instrucciones de operaciones Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Cocinas Dimplex Westcott